MotorSocks

Manage and protect your accessory cables on your trolling motor. With Motor Sock no need to disconnect any wires, just wrap and go.

**PLEASE READ BEFORE PLACING AN ORDER FOR THE MOTOR SOCK FOR RIGGING CABLES**

  • We offer custom made MotorSocks to protect and manage your rigging cables.
  • All Motor Socks have heavy duty velcro that runs along the entire length of the product. No need to disconnect any cables or wiring, just wrap and velcro tight!
  • The best way to measure is to take a piece of rope or fishing line, run it along the same route as your hose but follow the outside bends. Lay the line flat then measure for accuracy.
  • Motor Socks for rigging cables are custom made from your measurements. All Motor Socks for rigging cables sales are final – no returns or exchanges.
**NEW** Cable Drive MotorSock Colors - 35.00

**NEW** Cable Drive MotorSock Colors - 35.00

One size fits all: Minnkota Ultrex, Fortrex, Maxxum, & Edge trolling motors.

Lowrance Ghost

Motorguide Tour, X3, and X5

Color :
Cable Drive Trolling MotorSock XL for Mega 360 - 40.00

Cable Drive Trolling MotorSock XL for Mega 360 - 40.00

We designed a wider Motor Sock for trolling motors to accommodate for multiple accessories cables including the large transducer adapter for the Humminbird bow mount Mega 360.

One size fits all: Minnkota Ultrex, Fortrex, Maxxum, & Edge trolling motors.

Color :
Cable Drive MotorSock - 35.00

Cable Drive MotorSock - 35.00

One size fits all: Minnkota Ultrex, Fortrex, Maxxum, & Edge trolling motors.

Lowrance Ghost

Motorguide Tour, X3, and X5

Color :
Electric Drive MotorSock - 35.00

Electric Drive MotorSock - 35.00

Fits Minnkota Ulterra, Terrova, Powerdrive, & Riptide.

Motorguide Xi3, Xi5

Shaft Length :
Color :
5 Inch - MotorSock for Rigging Cables - 40.00

5 Inch - MotorSock for Rigging Cables - 40.00

The 5″ width Motor Socks are specifically designed for your hydraulic steering lines and other smaller cables.

Measure the length required by using a piece of string and running it along the same route as the cable, follow the outside bends. Lay the rope flat and then measure for accuracy.

Color :
Section Length :
7 Inch - MotorSock for Rigging Cables - 50.00

7 Inch - MotorSock for Rigging Cables - 50.00

The 7″ width Motor Sock is designed for rigging cables without the rigging hose. These generally fit motor rigging cables that are bundled and zip tied together.

Motor Socks for rigging cables are custom made from your measurements. All Motor Socks for rigging cables sales are final – no returns or exchanges.

Color :
Section Length :
10 Inch - MotorSock for Rigging Cables - 50.00

10 Inch - MotorSock for Rigging Cables - 50.00

If you have the 3″ rigging hose, you’ll want to select the 10″ width sock.

Motor Socks for rigging cables are custom made from your measurements. All Motor Socks for rigging cables sales are final – no returns or exchanges.

Color :
Section Length :
10 Inch - 2 Sections - MotorSock for Rigging Cables - 60.00

10 Inch - 2 Sections - MotorSock for Rigging Cables - 60.00

If you have the 3″ rigging hose but your fuel line exits and you require (2) sections, this is the product you’ll require.

(2) measurements will be required. (1) the length from the fuel line fitting to the motor and (1) the length from the other side of the fuel line fitting to where the hose enters the hull. Input the measurements below in the drop down boxes for both sections.

NOTE: The primer bulb and fuel line will not be wrapped. See picture above for an example.

Motor Socks for rigging cables are custom made from your measurements. All Motor Socks for rigging cables sales are final – no returns or exchanges.

Color :
Section 1 :
Section 2 :